|
The new Framework Directive (Directive 2007/46/EC establishing a framework for the approval of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles) rules approval schemes of the new motor vehicles and their trailers in the European Union:〔 〕 *European Community Whole Vehicle Type Approval (ECWVTA), currently this applies to passenger cars. On the 29th October 2012, ECWVTA was extended to cover all new road vehicles and their trailers. *United Nations Economic Commission for Europe (UNECE) regulations. *National Small Series Type Approval (NSSTA) - the key advantages of this scheme are that some technical requirements may be reduced in comparison with ECWVTA; however, the number of vehicles that can be manufactured are limited. *Individual Vehicle Approval (IVA) The European Commission shall adopt amendments to this Directive which are necessary to lay down technical requirements for small series vehicles, vehicles approved under the individual approval procedure and 'special purpose vehicles'.〔 UNECE Regulations to which the Community has acceded and which are listed in Part I of Annex IV and in Annex XI of the frame Directive are part of the EC type-approval of a vehicle in the same way as the separate directives or regulations. They shall apply to the categories of vehicles listed in this Annexes. When the Community has decided to apply on a compulsory basis a UNECE Regulation for the purpose of EC vehicle type-approval in accordance with Article 4(4) of Decision 97/836/EC,〔(EUR-Lex – Decision 97/836 - EN )〕 the annexes to the Frame Directive shall be amended as appropriate in accordance with the regulatory procedure with scrutiny referred to in Article 40(2) .The UNECE Regulations listed in Part II of Annex IV are recognised as being equivalent to the corresponding separate directives or regulations in as much as they share the same scope and subject matter. Where the Community has decided to applya new UNECE Regulation or a UNECE Regulation as amended, Part II of Annex IV shall be amended as appropriate.〔http://eur-lex.europa.eu/LexUriServ/LexUriServ.do?uri=CELEX:32007L0046:EN:NOT〕 Automotive EC Directives and ECE Regulations require third party approval - testing, certification and production conformity assessment by an independent body. Each member state is required to appoint an Approval Authority to issue the approvals, and a Technical Service to carry out the testing to the Directives and Regulations. An approval issued by one Authority will be accepted in all the Member States.〔(Type Approval for Cars )〕 If a vehicle is produced in a very small quantity (e.g. M1 maximum 75 per year), single EU Member States can grant exception on a discretionary basis, however the validity of the Type Approval is limited to the boundaries of those Nations which concede to it.〔http://ec.europa.eu/enterprise/automotive/speeches_presentations/brussels_15052009.pdf〕 Cornerstones of the Type Approval process are:〔 *Application by the vehicle or component manufacturer *Testing by a technical service *Granting of the approval by an Approval Authority *Conformity of Production by the manufacturer in agreement with the Approval Authority *Certificate of Conformity by the manufacturer for the end-user There are multiple methods of type-approval:〔(Directive 2007/46 )〕 *multi-stage Type Approval: a procedure whereby one or more Member States certify that, depending on the state of completion, an incomplete or completed type of vehicle satisfies the relevant administrative provisions and technical requirements of this Directive *step-by-step Type Approval: a vehicle approval procedure consisting in the step-by-step collection of the whole set of EC type-approval certificates for the systems, components and separate technical units relating to the vehicle, and which leads, at the final stage, to the approval of the whole vehicle * *mixed Type Approval: means a step-by-step Type Approval procedure for which one or more system approvals are achieved during the final stage of the approval of the whole vehicle, without it being necessary to issue the EC Type Approval certificates for those systems *single-step Type Approval: a procedure consisting in the approval of a vehicle as a whole by means of a single operation EC Whole Vehicle Type Approval (also called Pan European Type Approval) is to prevent trade barriers, and at the same time guarantee the level of safety and restricted environmental influence of a vehicle. Thanks to that, the car can be registered in each European member state without additional national tests or approval. This harmonisation results in reduced costs and lead time for the manufacturer, importer as well as the consumer.〔(Minister Eurlings of the Netherland Ministry of Transport was handing over the first ever Pan European EV homologation certificate – to Think. / Press releases / Press Materia... )〕 Mandatory compliance date for ECWVTA for M1 vehicles was 2009-04-29.〔http://www.rsa.ie/SERVICES/upload/File/ECWVTA/implementation%20dates%20for%20ECWVTA.pdf〕 However cars that already have an ECWVTA but are imported from non EC countries often need to be re-approved when entering the EC.〔http://www.containersharing.org/en/homologation〕 In the United Kingdom, this function is performed by the Vehicle Certification Agency (VCA).〔(Vehicle Type Approval and ISO Certification through VCA worldwide )〕 This body has the power to issue International Organization for Standardization (ISO) certifications. == Electric vehicles == Electric vehicles are rules by Regulation No 100 of the Economic Commission for Europe of the United Nations (UNECE) — Uniform provisions concerning the approval of battery electric vehicles with regard to specific requirements for the construction, functional safety and hydrogen emission〔http://eur-lex.europa.eu/LexUriServ/LexUriServ.do?uri=CELEX:42009X0214%2801%29:EN:NOT〕 抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』 ■ウィキペディアで「Motor vehicle type approval」の詳細全文を読む スポンサード リンク
|